Automate your sample loading and cleaning with the ECS - Easy Clean Sampling System T E C H N I C A L B U L L E T I N 9 2 7 Rudolph Research Analytical serving its customers with Integrity, Quality, and Innovation for over fifty years. The Rudolph ECS - Easy Clean Sampling System is designed to automate sample loading and cleaning EASY CLEAN SAMPLING SYSTEM SIMPLIFY WITH ECS Using Rudolph’s ECS - Easy Clean Auto Sampler Rudolph Research Analytical • Automated sample introduction is simple; the operator brings the sample to the 29-Jan-2007 12:14:52 Density Calibration Information 3 1.09803 g/cm Air/Water 22-Jan-07 • Waste disposal density meter, refractometer or polarimeter in any Water at 20 Deg C 23-Jan-07 Measuring 3 of 5 Mean:1.0980; Min:1.0980; Max:1.0980; SD:0.0000 Method Information Method HCL • Programmable cleaning and drying container that has an opening and a sample Specific Gravity Sample ID 8421AZ 1.1000 Lot No. 2011-B17J • Minimal sample volume: 3-4 ml volume of 3 - 4 ml. A test tube or beaker is Mean:1.1000; Min:1.1000; Max:1.0000; SD:0.0000 Temperature (Deg C) Normality Set 20.00 Change commonly used in a lab and sampling from a can 6.0092 N Current 20.01 • Just place your sample in front of the HCL % wt or bottle is more common in industrial 19.95 % Start instrument and press start Degrees Baume Video environments. The operator presses the fill 12.94 °Be Menu Method Print Save Air Pump Rinse Automation button, waits a few seconds while the sample is taken from the sample vessel. Built in pump for auto drying From that point, operation is completely automatic. The sample is measured and the data Rinse 1 recorded. Depending on how the system is Rinse 2 configured the data may also be printed, saved as an Excel file or transferred to a LIMS system. Waste storage Once measurement is complete, the sample is blown to a waste storage vessel using the built in air pump. The measuring cell is flushed with a solvent that will dissolve the sample, flushed again with a second solvent like acetone or alcohol that is fast drying and then blown with air to dry the complete system. The dry and rinse times are programmable in Sample being introduced to the “Method Set Up.” Through a Windows interface, density meter via suction created DDM2911 the operator is able to select the amount of time by piston pump for each rinse and the amount of drying time for each unique sample. Tubing ECS Easy Clean Sampling System Automatic Refractometer Automatic Polarimeter Autopol V or VI J57WR-SP Polarimeter Cell ECS Easy Clean Sampling System ECS - Easy Clean Sampling System Specifications Max. sample viscosity 3000 mPa.s Auto cleaning detection Yes - Instrument will continue Filling mode Piston Pump to rinse and dry until all sample is removed Number of rinse solutions 2 separate rinses standard Expandability System can pump sample through Rinse level detection Yes - lightgate up to 5 separate instruments Rinse Time Programmable & method specific Sample recovery Yes - sample can be redeposited Waste level detection Yes - floatgate into sample vessel Minimum sample volume necessary Operating Dimensions L x W x H 9.5 x 13 x 10.5" / 24 x 33 x 27 cm for measurement 3 - 4 ml Operating Weight 11 lbs. / 5kg Filling, measuring, and cleaning time 3 - 6 minutes typical Shipping Dimensions L x W x H 27 x 20 x 17" / 66 x 54 x 40 cm Fill level detection Yes - lightgate Shipping Weight 21 lbs / 9kg Drying Time Programmable & method specific Power Requirements 100 - 240V / 50 - 60Hz Rudolph Research Analytical 55 Newburgh Road, Hackettstown, NJ 07840 USA • Phone: 973-584-1558 • Fax: 973-584-5440 • E-mail: info@rudolphresearch.com • Internet: www.rudolphresearch.com 05/09